← Back to blog

Plate Cover Compatibility Check: Fit, Hardware and State Rules

Hand-drawn plate-fit title card with measurement details

A plate cover is compatible when it matches your plate’s size and bolt-hole pattern, bolts to your vehicle’s mount with hardware that threads correctly, clears the bumper and trim around it, and is allowed where you plan to use it. Most U.S. passenger plates follow one standard, so the first three checks take about ten minutes with a tape measure. The state-rule check is the one that decides how and where you can use the cover. Our Ghost Curtain Cover is built for universal fit on standard U.S. and Canadian plates with tool-free installation, which removes most of the guesswork from the fit steps below.

Goghost
Check Fit Before Choosing a Cover
GoGhost offers electric and mechanical plate covers designed for universal fit on standard U.S. and Canadian plates.
Visit

TL;DR

  • Standard U.S. car plates are 12 inches by 6 inches. Motorcycle plates are smaller, so measure before you order.
  • Check the bolt-hole spacing and the screw type on your vehicle. Hardware is where most fit problems start.
  • Look at the space around the plate: recessed mounts, bumper lips, frames and sensors all affect how flat a cover sits.
  • Covers that hide any part of a plate are restricted or banned on public roads in many states. Read your state’s statute before you fit anything.
  • Our Ghost Curtain Cover is $129.99 and fits standard U.S. and Canadian plates without tools.

Table of Contents

Step 1: Confirm your plate size

Start with the plate itself, not the car. Passenger car, truck, bus and trailer plates in Texas measure 12 inches by 6 inches, and Alabama’s own specification lists the finished passenger plate as 6 by 12 inches. That is no coincidence. The AAMVA License Plate Standard, which the motor vehicle administrators’ association publishes, states that plate dimensions and bolt holes follow SAE International’s J686 standard. In practice, a cover made for a 12 by 6 inch plate fits a car plate from nearly every state.

Measure anyway. Hold a tape measure across the widest part of the plate, edge to edge, and write down width and height. Then look for three exceptions:

  • Motorcycle plates. Texas motorcycle plates measure 7 inches by 4 inches, far smaller than a car plate. A car-size cover will not fit one, and the reverse is also true. Our guide to car vs motorcycle plate covers is not needed here; the point is to order the size that matches your plate.
  • Specialty and vanity plates. Most keep the standard outline, but raised borders, embossed logos or unusual shapes can stop a flat cover from sitting flush.
  • Dealer, temporary and paper tags. These are often mounted in a holder or behind glass. A cover built for a metal plate is not designed for them.

For a deeper look at measurements, our post on U.S. license plate cover dimensions walks through the numbers.

Step 2: Check the bolt-hole pattern

Size tells you the outline. The holes tell you whether the cover will mount. On a standard car plate, the bolt holes sit 7 inches apart horizontally and 4¾ inches apart vertically, measured center to center, and Texas lists each hole as ½ inch wide by 0.28 inch tall. The holes are slightly elongated, which gives you a little room to nudge a plate left or right. Motorcycle plates use a tighter pattern: 5 13/16 inches horizontally and 2¾ inches vertically, with round 5/16-inch holes, according to the same document.

How to check it:

  1. Measure from the center of the left hole to the center of the right hole on the same row. You are looking for about 7 inches on a car plate.
  2. Measure from the center of a top hole to the center of the bottom hole in the same column. You are looking for about 4¾ inches.
  3. Count the holes. Most plates have two on top. Some vehicles use four, with two more at the bottom.

If your numbers match, a standard cover lines up with your plate and the vehicle’s mount. If they do not, the plate may be a non-standard type, or the mount on your vehicle may use a different pattern. Our guide to 7-inch license plate hole spacing covers the common fixes.

The Ghost Curtain Cover is designed for universal fit on all standard U.S. and Canadian plates, so a plate that passes these two measurements is the plate it is made for.

Step 3: Match the hardware to your vehicle

The plate may be standard while your vehicle’s mounting hardware is not. Screw size and thread type vary by make and model, and some vehicles use plastic push-in fasteners or a bracket instead of bare screws. Identify what you have before you buy:

  • Look at the screw head and thread. Metric thread and inch-based thread are not interchangeable. Forcing the wrong one strips the hole in the bracket or bumper.
  • Check the mounting holes behind the plate. Some front bumpers have threaded inserts, and some have bare holes that take self-tapping screws.
  • Note whether you have two points or four. A plate held at only the top two holes can flex and rattle, which matters for any cover that adds thickness or weight.
  • Keep your original screws. If a cover’s included hardware does not fit, the originals are your fallback.

Our plate cover mounting hardware checklist lists the common screw types for U.S. vehicles so you can match yours.

A loose plate is a separate problem from an incompatible cover, but it often shows up at this step. If your plate rattles or has gone missing before, read about fixing a loose license plate before you add anything to the mount.

Our cover installs without tools, so you are not hunting for a specific driver size. You still need to be sure the plate is held on securely beneath it.

Step 4: Check clearance and installation space

A cover can match the plate and still sit badly on the car. Walk around to the plate and check four things.

Recess depth. Many trucks and SUVs set the plate in a molded pocket in the bumper or tailgate. Look at how deep the pocket is and whether trim overhangs its edge. A flat cover with a lip needs room on all four sides.

Curvature. Some bumpers curve across the plate area. A rigid cover on a curved surface can leave a gap at the edges where water and dirt get in. Hold a straightedge, such as a ruler, across the mount to see whether it is flat.

Frames. A plate frame adds thickness and covers the border. Remove it for the fit check, because a frame can stop a cover from seating and can hide screw holes.

Nearby hardware. Look for a rear camera, parking sensors, a license plate light, a tow hook cover or a trailer hitch ball sitting near the plate. Make sure the cover does not press on any of them or block the plate light.

Two simple tests help. First, hold the cover or a same-size piece of cardboard against the mount and check that nothing touches the bumper edge. Second, check that you can still reach the screws. A cover that traps the hardware behind it will be a chore to remove for a car wash or an inspection.

Four checks for plate cover clearance

For trucks and crossovers, our write-up on SUV rear plate privacy covers the usual clearance quirks. Our covers are weather-sealed, which helps with rain, road spray and dust once the cover is seated flat.

Step 5: Check your state’s rules before you install

Fit is only half of compatibility. A cover that mounts perfectly can still be unlawful to drive with, and the rules differ sharply by state. This is the step where the cover’s intended use matters most.

Here is how far the statutes diverge:

State What the rule says
California Plates must be clearly visible and legible, and coverings are barred except for weather protection on a lawfully parked vehicle or a security cover limited to the area over the tabs. Since 1 January 2026, devices that impair reading by law enforcement, toll or emissions sensors are also prohibited.
Washington Plates must be kept clean, uncovered and legible. Covers that conceal or obstruct a plate are unlawful.
Maryland It is illegal to use or sell a tinted, colored or illuminated cover that blocks any part of the plate.
Indiana The rear plate must be fully visible, not obscured by frames or covers, and mounted at least 12 inches off the ground.
Utah An individual may not attach a cover to or over a plate, and the plate must be free of any tinted or translucent cover. A violation is an infraction.
Illinois Operating a vehicle with a plate cover is unlawful, with a $750 fine for covers designed to obstruct traffic cameras according to 2023 reporting.

The common thread is legibility. AAMVA’s policy position is that plates should remain unobscured and visible from at least 75 feet, including for license plate readers. A blackout cover that hides a plate is, by design, the opposite of that.

So here is the plain guidance. On public roads, a cover that hides your plate is restricted or prohibited in many states, and tolls and camera enforcement are exactly where those rules apply. We make our covers for off-road driving, motorsport, track days, shows and private property, where plate visibility rules do not govern the surface you are on. Before you drive on any public road with a cover installed, confirm what your state allows. If you are unsure, the state’s motor vehicle agency or a licensed attorney in your state is the right person to ask. If a cover has already earned you a citation, our five-step guide to a plate cover ticket explains the usual process.

How to look up your state’s current rule

Statutes change, and a rule that was true when a blog post went up may have been amended since. California’s 2026 amendment is a good example. To check your own state:

  1. Search for your state’s name plus “vehicle code license plate display” and open the result on a .gov or official legislature site.
  2. Find the section on how plates must be displayed. Look for words like “covered,” “obscured,” “tinted,” “frame” and “cover.”
  3. Check the date or effective year at the top of the page, and see whether a newer amendment is noted.
  4. Check the state motor vehicle agency’s plate page. It often explains the rule in plain language.
  5. If your trips cross state lines, check each state you drive in. The strictest rule on your route is the one that matters there.

Our breakdown of U.S. plate cover laws since 2026 collects the main changes in one place, and our overview of license plate privacy options compares the five main types of cover.

A quick compatibility worksheet

Write these down before you order. If every line has an answer, you can buy with confidence.

Check What to record Standard car plate reference
Plate size Width and height 12 in by 6 in
Hole spacing Horizontal and vertical, center to center 7 in by 4¾ in
Number of holes Two or four Two is common
Screw type Metric or inch, plus the length you have Varies by make
Mount depth Flat, recessed or curved Varies by vehicle
Nearby parts Camera, sensor, plate light, tow hook Varies by vehicle
State rule Statute section and its date Varies by state

Motorcycle owners should use the motorcycle reference: 7 in by 4 in plate and 5 13/16 in by 2¾ in hole pattern.

Perspective

Fit problems are the most common reason a plate accessory ends up in a drawer, and almost all of them could have been caught with a tape measure. That is why we design around the standard U.S. and Canadian plate and keep installation tool-free: the fewer variables between a box arriving and a cover sitting flat, the better.

We also offer both electric and mechanical covers, because drivers do not all need the same thing. The electric model uses electric glass technology and a wireless remote. The mechanical model uses a manual sliding curtain and needs no power. Either way, the same fit checks apply, and the same responsibility does too: know your state’s rules, and use the cover where it belongs, on the track, off-road, at shows and on private property.

A cover that fits well and stays sealed against weather is a better product than one that merely bolts on. That is the standard we build to.

GoGhost

Ready to order? Start with the Ghost Curtain Cover

If your measurements match the standard plate, the Ghost Curtain Cover is the one to look at. It is a manual sliding-curtain cover for standard U.S. and Canadian plates, installs without tools and is weather-sealed. It is priced at $129.99. If you would rather see what other drivers say first, the customer reviews are on our site.

Goghost

We ship same day, so a measurement session on Saturday morning can be a fitted cover soon after.

FAQ

Does a standard plate cover fit every car?

Most U.S. car plates are 12 inches by 6 inches with a common bolt-hole pattern, so a cover made for that size fits the plate on nearly every passenger vehicle. The variables are your vehicle’s mount, its hardware and the space around the plate. Run the five steps above to confirm.

Will a car plate cover fit a motorcycle?

No. A motorcycle plate is smaller, at 7 inches by 4 inches in Texas, and uses a tighter hole pattern. Order the cover made for your vehicle type and measure the plate before you buy.

What if my screws do not match the cover’s hardware?

First work out whether your vehicle uses metric or inch-based threads, since mixing them strips the holes. Then compare screw length against the mount depth. Our mounting hardware checklist lists the common types to help you match them.

In many states it is not. California, Washington, Maryland, Utah and Illinois all restrict covers that obstruct a plate, and some now address camera and toll readers directly. Check your state’s statute before driving on public roads, and use covers where plate visibility rules do not apply, such as track and off-road settings.

How do I find my state’s current rule?

Search your state’s official legislature site for its license plate display section, then check the effective date and any recent amendment. Your state’s motor vehicle agency page is a good second check.

Sources