← Back to blog

Ignition-Switched Power for a Plate Cover: How It Works

Hand-drawn automotive electrical title card

Ignition-switched power is a 12-volt feed that is live only when the key or start button puts the vehicle in accessory or run. For an electrically operated plate cover, that means the cover has power while the car is on and none when it is parked. You find the circuit with a multimeter or test light, tap it through a fused connection, and ground the cover to clean metal. This guide covers each step, then the legal points you need to check before you wire anything to a plate.

Goghost
Explore Electric and Mechanical Covers
GoGhost offers electric and mechanical plate covers, including a manual option that does not rely on an ignition-switched circuit.
Explore plate covers

TL;DR

  • Switched (ACC or ignition) power is a 12V source that turns on with the key in accessory or run and drops to zero when the key is out.
  • To identify the right wire or fuse slot, ground a test light or meter to bare metal and confirm voltage appears only with the key on, as described in this wiring guide.
  • Fuse the tap, route wires away from heat and moving parts, and disconnect the battery before you start.
  • Plate cover rules differ by state, and several states restrict covers that obscure a plate or defeat cameras. Check your state before you buy or install.
  • Our mechanical Ghost Curtain Cover is manual, so it does not depend on a switched circuit at all.

Table of Contents

What ignition-switched power means

A car has two basic kinds of 12V feed. A constant feed stays energized whatever the key position. A switched feed follows the ignition. According to one car-audio explainer, a switched ACC wire reads about 0V with the key removed, about 12V in accessory, and roughly 12 to 14V with the engine running.

ACC and constant feed voltage by key position

That behavior is why installers choose it for anything that should only work while the vehicle is in use. Nothing sits drawing current overnight, and the accessory shuts off on its own when you leave. Some vehicles keep switched circuits alive briefly after the engine stops as part of retained accessory power, so do not assume the feed drops the instant the key turns.

Accessory vs. ignition (run) circuits

The two switched types are close cousins but not identical.

Circuit Live when Typical use
Constant 12V Always Memory, alarms, clocks
Accessory (ACC) Key in ACC, and often ON Radios, small electronics
Ignition / run (ON) Key in ON or engine running Higher-current gear, relays

The ignition (on) source is the most common choice for electronic devices that draw a lot of current, and it stays live with the key in the on position even if the engine is off. Vehicle makers also use it for relay control: GM’s upfitter guidance for one commercial van describes a 10-amp fused ignition (run mode) circuit so connected equipment is active only in run mode.

Vehicles vary. Renogy advises checking the vehicle’s own instructions or schematics because wire colors and circuit layouts differ by model. Treat any wire color you read online as a hint, never as proof.

Where a plate cover can get switched power

There are three practical places to pick up a switched 12V feed near the rear of a car, and one at the front.

  1. The fuse box. Many fuse boxes include slots that are live only with the ignition on. A fuse box can have tabs or spades for both accessory and constant 12V, so you test each one instead of trusting the diagram.
  2. The ignition harness. The switched side of the harness carries the feed directly. It is also the more invasive spot to work, which matters when we get to professional help below.
  3. An existing switched circuit. Some installers pick up power from a circuit already on when the car is on, such as an accessory socket or a lamp feed. Use a fused connection and confirm the circuit can carry the added load.
  4. The plate lamp area. The wiring that feeds the rear plate lamp is accessible near the plate. Be aware that plate lamps are typically switched by the light switch, not the ignition, so that feed may not match what you want. In some vehicles the lamp wire is a switched battery positive from the ignition switch, but you should verify that on your own vehicle.

How to identify the correct circuit

You need a digital multimeter or a 12V test light. The method is the same for every vehicle.

  1. Set the meter to 12V DC, or take a test light.
  2. Clip the ground lead to clean, bare metal on the chassis, not a painted bolt.
  3. With the key off, probe the candidate fuse slot or wire. It should read nothing.
  4. Turn the key to ON or ACC and probe again. You want about 12V.
  5. Turn the key off once more and confirm the voltage disappears.

That sequence follows the identification method in this wiring knowledge base: voltage should vanish with the key off and return in ON, ACC or run. A multimeter reading about 12V only in the key-on position is the confirmation you want.

If a slot reads 12V in every key position, it is constant power. If it reads 12V in ACC but dies during cranking, it is an accessory circuit. Either may work for a low-draw device, but note which one you chose.

Connecting the cover: fuse and wiring precautions

Good wiring is boring. The goal is a connection that never gets hot, chafed or loose.

  • Disconnect the battery first. An industry installation sheet for a plate light tells installers to disconnect the vehicle battery before starting, feed wires through existing plate holes, and connect positive to 12V and the black wire to ground.
  • Fuse the tap. Use an add-a-circuit fuse tap or an inline fuse placed close to the power source, rated for the device’s draw. Follow the cover maker’s amperage instructions.
  • Crimp and seal. One plate wiring guide has installers crimp butt connectors on the red and black wires and seal them with a heat gun. Heat-shrink connectors beat twisted wire and tape.
  • Route away from hazards. The same guide says to keep wires away from hot or moving parts and secure them. On a trunk lid, leave slack at the hinge so the harness is not stretched or pinched.
  • Test before you tidy. Reconnect the battery, confirm the device works, then secure the harness with cable ties.
  • Ground to bare metal. A poor ground causes flicker and intermittent failure more than any other fault.

Water is the other enemy. A plate sits at the back of the car, exposed to spray, road salt and car washes. Keep connections inside the vehicle where you can, and seal any that must stay outside.

Will it fit your vehicle?

Before you plan any wiring, confirm the physical basics.

  • Plate size. US and Canadian standard plates measure 12 inches by 6 inches. Our guide to license plate cover dimensions walks through measuring first.
  • Mounting holes. Check the hole spacing on your car’s plate bracket, which can differ on some European imports and on motorcycles.
  • Wire path. Look for a grommet or existing opening between the plate area and the cabin or trunk. Many plate lights already use one.
  • Recess and trim. Deep recessed plate pockets and plate frames change what fits.
  • Front plate. Front plates have a longer run to the fuse box, which affects wire length and routing. See our overview of front and rear plate covers.

Our products are designed for universal fit on standard US and Canadian plates, and installation is tool-free.

When to call an automotive electrician

A fuse tap and a ground screw are within reach of many careful owners. Some jobs are not. Consider a professional automotive electrician when:

  • Your vehicle’s manual or schematic does not clearly identify the circuit you want, or the meter results confuse you.
  • The only route is splicing the ignition harness behind the switch or steering column, close to airbag wiring.
  • You are not comfortable working near the battery or the fuse panel.
  • The vehicle is hybrid or electric, where high-voltage systems and unusual 12V architecture apply. Follow the manufacturer’s instructions and have a qualified technician handle it.
  • A circuit blows its fuse again after you have replaced it. Repeated blowing signals a fault, not a bad fuse.
  • The vehicle is under warranty and the dealer has specific rules on aftermarket wiring.

A shop can also test the draw and verify the circuit behaves, which is the same check you would do yourself, only faster.

US law: check before you install

This is the part of the topic you cannot skip. Plate cover rules are state law, and many states restrict anything that blocks or distorts a plate. The examples below show how varied they are, and they are not a full list.

State What the law says
New York Since September 1, 2024, plates may not be covered by glass or any plastic material, and selling plate covers that obscure a plate is unlawful, with fines of $100 to $500.
California From January 1, 2026, selling a product that obscures a plate from visual or electronic reading is a violation, with a $1,000 fine per item and a $250 fine for operating a vehicle with one.
Maryland Section 13-411.1 defines and bans registration plate covers that block characters or distort a recorded image.
New Jersey Section 39:3-33c covers retractable holders and anti-photograph covers meant to conceal a plate to evade law enforcement, with fines up to $500.
Utah Plates must be readable from 100 feet in daylight, and covers that block readability are an infraction.

More states are acting too. Trade press reports that five states have moved against plate flippers, including manual, electric and mechanical devices, partly because of lost toll revenue.

What this means in practice: use a blackout plate cover only where your state and local rules allow it. Our product is designed for private property, off-road, closed-course and motorsport use, such as at track days and shows. Before you use any cover on a public road, read your state’s statute or ask your DMV or state police. For a state-by-state overview, see our guide to license plate cover laws, and if you have already been stopped, read the five steps for a plate cover ticket.

Our perspective

We built GoGhost around a simple observation: the wiring is where most owners lose patience. A cover that needs a hunt through the fuse box, a meter and a splice is a project, and projects stall.

That is why we offer both an electric and a mechanical option. The electric model uses electric glass and a wireless remote, so you flip a switch and the plate goes dark instantly. The mechanical model uses a manual sliding curtain, so there is nothing to wire and nothing to fuse. Both are designed to fit standard US and Canadian plates, both are weather-sealed, and both install without tools.

If you like the idea of power that follows the ignition, the wiring advice above will serve you well, and the same discipline applies to every accessory you add: fuse it, seal it, ground it, test it. If you would rather skip the circuit work entirely, the manual curtain gives you the same on-demand control with no electrical risk.

Whichever you choose, check your state’s rules first and keep use to settings where covering a plate is permitted.

GoGhost

The no-wiring option

If the idea of probing fuse slots does not appeal, our Ghost Curtain Cover is a manual blackout cover: a sliding curtain you operate by hand, built weather-sealed and designed for universal fit on standard US and Canadian plates. It installs without tools and costs $129.99. You can see details and order on the Ghost Curtain Cover page.

Goghost

Over 10,000 drivers use GoGhost covers, and our store holds a 4.9-star rating from nearly 3,000 reviews, which you can browse on our reviews page. We ship the same day. For help choosing between plate privacy approaches, our guide to license plate privacy options compares the types.

Checking your setup before you drive

After any install, run a short checklist.

  1. Turn the ignition on and off three times and confirm the device responds each time.
  2. Wiggle the harness gently at the plate and the hinge, watching for flicker.
  3. Wash or spray the area and recheck for moisture.
  4. Confirm the battery drain is nil with the car off.
  5. Check readability from a distance. Our plate cover highway test shows how.
  6. Recheck the fuse and connections after the first week, since vibration finds weak crimps.

For more detail on mounting, see our guide to mechanical and electric cover installation. Browse more guides on the GoGhost blog.

FAQ

Where does ignition-switched power come from?

It comes from the ignition switch, which sends 12V to a switched circuit when the key is in accessory or run. You can tap it at a fuse box slot that is live only with the key on, or at the switched side of the ignition harness. Confirm it with a meter before connecting anything.

What is the difference between constant and switched power?

Constant power stays live in every key position. Switched power reads 0V with the key out and about 12V in accessory. Use switched power for devices that should only run while the vehicle is on.

Do I need a fuse for a switched connection?

Yes. Put a fuse on the tap, close to the power source and rated for the device. Disconnect the battery before you start, and keep the wires away from heat and moving parts.

Does the Ghost Curtain Cover need a power connection?

No. The Ghost Curtain Cover is our mechanical model with a manual sliding curtain, so it does not need to be wired to a switched circuit. It installs without tools.

In many states it is not. New York, California, Maryland, New Jersey and Utah all restrict covers that obscure plates, as listed above. Check your state’s statute before any public-road use.

Sources