Bull Bar Plate Cover Fitment: How to Get It Right

A plate cover fits a bull bar setup when three things line up: the plate sits flat on a solid relocation bracket, the bracket’s mounting holes take standard plate screws, and there is clearance around the plate for the cover to open and close. Most fitment trouble comes from the bracket and the bar, not the cover. Sort out the bracket first, then measure, then fit the cover.
TL;DR
- A bull bar usually blocks the factory plate spot, so the plate moves to a relocation bracket made for your bar or your vehicle.
- The cover goes over a standard 12 in. by 6 in. plate, so the job is a flat, rigid plate with clear space around it.
- Check hardware, hole spacing and clearance before you order, and recheck bolt tightness regularly because bars vibrate.
- Our covers are made for off-road, motorsport and show use. On public roads, your plate must stay clearly readable under your state’s law.
- Our Ghost Curtain Cover is $129.99 and is built for universal fit on standard U.S. and Canadian plates.
Table of Contents
- Why a bull bar changes plate fitment
- Does a plate bracket attach straight to the bar?
- The fitment checklist
- Fitment quick reference
- Installing the bracket the right way
- Motorcycles, side mounts and tow-hook setups
- Keeping it secure on and off the road
- Plate visibility rules to follow
- Our perspective on bull bar plate covers
- A cover built for off-road and motorsport use
- FAQ
- Sources
Why a bull bar changes plate fitment
A bull bar or grille guard sits where many front plates are mounted, so the plate has to move. Bar makers say as much: ARIES notes that installing a grille guard, bull bar or bumper may mean relocating your plate to stay legal. Where the plate goes next decides everything about the cover.
There are three common spots:
- A bracket bolted to the bar’s skid plate or cross tube. This is the cleanest option and the one most kits are built around.
- A vehicle-specific relocation kit that uses factory points such as tow-hook bolts or a frame U-bolt.
- A bumper-mounted or low-mounted holder. This is the weakest option. Owners on enthusiast forums describe plates held only by small plastic bumper holes as flimsy, and a flexing plate is the worst base for a cover.
A cover is only as stable as the plate behind it. If the plate wobbles, the cover rattles, and a sliding or electric mechanism will not sit square.
Does a plate bracket attach straight to the bar?
Sometimes, but not universally. The answer depends on the bar.
The ARIES 2169000 bracket is designed for attachment to the bull bar skid plate, and the plate then bolts to the bracket. Black Horse takes a different route with its C59 bracket: according to its installation instructions, the bracket sits against the cross tube over the skid plate, is held by two adhesive foam strips, and is secured by the center skid-plate bolt.
Other bars need a vehicle-specific kit. The Westin Ultimate Bull Bar instructions for listed Ford Expedition, Lincoln Navigator and Ford F-150 applications say the original plate and bracket may need removal, and they name relocation kit 32-0055 where local or state law requires a plate.
The takeaway: do not assume any bracket fits any bar. Match the bracket to the bar brand and model, and to your vehicle.

The fitment checklist
Work through this before you buy a cover. It takes about ten minutes with a tape measure.
1. Identify your bar and your bracket
Find the bar’s part number and the bracket’s part number. Check that the bracket lists your year, make and model. One Steelcraft kit, for example, lists a range of Silverado, F-150 and Ram 1500 model years, so the year range matters.
2. Check for factory tow hooks
This is a real fork in the road. In the listed Westin applications, the instructions use the existing tow-hook bolts when the vehicle has them and a frame U-bolt when it does not. Two trucks of the same model can need different hardware.
3. Confirm the plate screws
The plate must attach with the fasteners the bracket expects. The ARIES bracket uses four M6 screws and flange nuts to hold the plate, and the Black Horse C59 uses two 6 mm screws. Our guide to plate cover mounting hardware walks through M6, 1/4 in. and No. 14 sizes so you can match your screws.
4. Measure the hole spacing
U.S. plates use a standard hole pattern, but brackets can differ in how they present it. Some have two slots, some four holes. If your bracket has only two holes, a cover that expects four mounting points needs a different approach. See our note on 7 inch plate hole spacing and fixes for how to measure and what to do if the pattern is off.
5. Measure the plate area
A U.S. plate is 12 inches by 6 inches, but the cover and any frame add thickness and edge space. Our guide to license plate cover dimensions shows how to measure the full footprint. Then look at the bracket: are there bar tubes, a winch fairlead, or a light pod within a couple of inches of the plate edges? If so, the cover needs room to work.
6. Allow for frame clearance
If you run a plate frame, the frame sits between the plate and the cover. Use our plate frame clearance guide to work out how much space it takes up.
7. Think about the bar’s own hardware
Skid-plate screws, foam strips and cross tubes all change the plate’s depth from the bar. A bracket that holds the plate a half inch off the tube may suit a cover differently from one that sits tight. Hold the plate and cover up to the mounted bracket before committing.
Fitment quick reference
| Check | What to look for | Why it matters for a cover |
|---|---|---|
| Bracket match | Lists your bar and vehicle model | A loose or flexing plate shifts the cover |
| Tow hooks | Factory hooks or frame U-bolt route | Decides which bracket kit you need |
| Screw size | M6 is common, 1/4 in. and No. 14 also used | The cover’s mounting must use the same holes |
| Hole pattern | Standard U.S. spacing | Needed for a flat, secure fit |
| Plate footprint | 12 in. by 6 in. plus cover edge | Tubes and lights must not block movement |
| Depth | Space behind plate and between plate and cover | Prevents rubbing and rattling |
Installing the bracket the right way
The install is where bad fitment is born, and the manufacturers’ own instructions give useful detail.
Do the bracket first, if you can. Westin states it is usually easier to install the plate relocator on the bull bar before installing the bar on the vehicle. You get better access and can set the plate position on a bench.
Gather the right tools. The ARIES 2169000 manual lists a 10 mm wrench, a T20 Torx bit and a Phillips screwdriver. The steps are: remove the four skid-plate screws, secure the bracket to the skid plate with the supplied thread-forming screws, then attach the plate with four M6 screws and flange nuts, per the ARIES manual.
Respect torque values. They vary by bar, so use your own instructions. For reference, Westin’s listed Ultimate Bull Bar values are 19 ft-lb for 3/8 in. fasteners and 50 ft-lb for M12 fasteners. A different Westin Toyota set calls for 79 ft-lb on M12 bolts and 37 ft-lb on 1/2 in. stainless fasteners. The ARIES Ranger sheet lists 10 ft-lb for 6 mm fasteners. Those figures are for those specific bars, not a universal spec.
Fit the cover last. Once the plate is bolted down and the bar is mounted, test the cover’s position. Our tool-free plate cover install guide covers the steps.
Motorcycles, side mounts and tow-hook setups
Not every relocated plate faces forward on a bar. Some builds put a plate on a side bracket or near a tow hook, and motorcycle plates have their own geometry. If that is your setup, read our side mount plate cover fit guide and the motorcycle quick-release install walkthrough before measuring.
Keeping it secure on and off the road
Bull bars take vibration, mud and trail hits. ARIES calls for periodic inspections to make sure all mounting hardware remains tight. Make that a habit:
- Check plate screws, bracket bolts and bar bolts after the first drive, then at your regular service intervals.
- After a trail run, wipe the plate and cover and look for cracked brackets or bent tubes.
- Look for rubbing between the cover and any bar tube.
Our covers are weather-sealed, which helps when the plate takes spray and dust, but a loose bracket is still the first thing to fail.
Plate visibility rules to follow
Fitment is also about the law. Moving a plate onto a bull bar does not change your duty to display it properly, and rules differ by state.
Michigan is a clear example. Its law requires a plate to be securely fastened horizontally, at least 12 inches from the ground measured from the plate bottom, clearly visible and free of material that obscures registration information. The same section bars attaching an insignia or advertising device that obscures or partly obscures the plate, and a violation is a civil infraction. Separately, Michigan requires plate letters and numerals to be plainly readable from 100 feet in daylight and the standard plate to be fully reflectorized.
California describes the standard differently. A California DMV report says plates must be reflectorized and readable from at least 75 feet.
The practical rule: on public roads, keep your plate clearly visible, mounted at a legal height and angle, with nothing covering it. Check your own state’s statute and, if you are unsure, your DMV or state police. A low bull bar bracket can put the plate under a height limit, and a bar tube across the plate face can break a visibility rule.

That is why we design our covers for off-road, motorsport and show use, and for private property where a plate display is not required. For help with readability checks, use our plate cover highway test, and for a wider look at your options, see our guide to license plate privacy options and U.S. rules.
Our perspective on bull bar plate covers
Most bull bar owners come to us after a frustrating hour with a tape measure. The bar is on, the plate is on a bracket, and nothing about the setup looks like the flat factory spot a cover expects.
Our answer is to remove variables. The Ghost Curtain Cover is designed for universal fit on standard U.S. and Canadian plates, and it installs without tools. That matters on a bar, where you often cannot get a socket behind the plate once everything is bolted on.
We also offer both electric and mechanical options. An electric cover needs a power route and a place for the wiring; a mechanical sliding curtain does not. On a trail truck where wiring is exposed to brush and water, many drivers will find the mechanical curtain the simpler fit. We built both so you choose the one that suits your bar, not the other way round.
Our advice is to fit the bracket first, torque it to the bar maker’s spec, and then fit the cover on a plate that does not move. Do it in that order and fitment is straightforward.
GoGhost
A cover built for off-road and motorsport use
If your plate is on a bracket and you want a cover that fits standard 12 in. by 6 in. plates, the Ghost Curtain Cover is $129.99. It is a manual sliding curtain, weather-sealed, with tool-free installation, so you do not need to fight for wrench room behind a bull bar.

Thousands of drivers have used our covers, and our storefront shows a 4.9-star rating from nearly 3,000 reviews. You can read what customers say on our reviews page, or browse the GoGhost blog for more fitment guides. Orders ship the same day.
FAQ
Can I put a plate cover on a plate mounted to a bull bar?
Yes, as long as the plate is a standard 12 in. by 6 in. plate held flat and rigid on a bracket, with clear space around it. Check hole spacing, screw size and clearance first. Then fit the cover on top once the plate is secure.
Do I need a vehicle-specific relocation kit?
Often, yes. Westin’s listed applications use a specific relocation kit, and the mounting method changes depending on whether your vehicle has factory tow hooks. ARIES and Black Horse brackets each attach to the bar in a different way, so match the bracket to your bar and vehicle.
What tools do I need?
For the ARIES 2169000 bracket, you need a 10 mm wrench, a T20 Torx bit and a Phillips screwdriver. Your bar may call for different tools, so follow its own instructions. Our cover itself installs without tools.
How tight should the bolts be?
Use the torque values in your bar’s instructions. They vary: Westin lists 19 ft-lb for 3/8 in. fasteners on one bar, while an ARIES Ranger sheet lists 10 ft-lb for 6 mm fasteners. Recheck tightness regularly, since bars vibrate.
Can I drive on public roads with my plate hidden?
No. State laws require a plate to be clearly visible and not obscured, as Michigan’s statute shows. Use blackout covers off-road, at motorsport events, at shows or on private property, and keep your plate readable on public roads.
Sources
- ARIES 2169000 installation manual
- ARIES Ranger installation sheet 35-3011
- Westin Ultimate Bull Bar installation instructions 75-0800
- Westin Toyota installation instructions 75-0763
- Black Horse Bull Bars installation instructions
- Michigan Compiled Laws 257.225
- Michigan Compiled Laws 257.224
- California DMV SB 1387 report